How do you troubleshoot PetSafe invisible fence?
Why is my invisible fence not working?
My pet’s Invisible Fence collar doesn’t activate at the boundary, what is wrong? Ensure that
your pet’s Computer Collar receiver is fitted properly to his neck. The collar should be snug enough to slide only one finger between a correction post and your pet’s skin.
Why is my electric dog fence not working?
Check to make sure the collar battery is inserted positive end facing upward.
Try resetting the frequency of your dog fence collars, to a setting of 01 on your transmitter. Try testing the collar by holding it at the height of your dog’s neck, which is around your knees.
Why is my PetSafe collar beeping but not shocking?
Touch both points on the collar while it is ticking or beeping. If you do not feel a shock, then there may be a problem with the receiver collar. Make sure you touch both points on the receiver at the same time when you hear the collar beeping. It will tell you definitively that the fence is or is not working.
How do I know if my petsafe transmitter is bad?
To check if the transmitter is having issues you’ll need
to disconnect the existing boundary wire and connect a short 15-foot section of boundary wire to run some tests. Make sure the 15-foot wire is spread out. The signal will cancel anywhere the wire is within 3 feet of itself.
How do you find a broken invisible fence?
Take an
extra length of wire and run it over a section of underground wire. Carefully dig out the underground wire at both ends of the run. Cut the underground wire at both ends and connect the above-ground wire to make a bypass. If the transmitter stops beeping you found the break.
Why is my wireless PetSafe collar not working?
Collar Power
Use the test light tool or a coin to remove the battery from the collar. Lift the metal tab or spring gently to ensure the battery will firmly touch the tab when installed. Press and hold mode button on collar for 20 seconds. … If the collar does not power on, replace the battery with a new RFA-67 battery.
How do you turn up the shock on Invisible Fence?
Adjust the Power Level
After checking the current level, press the button again within 5 seconds to raise the correction level. The collar will beep or blink in series to indicate the new shock level. Press the button again within 5 seconds to raise the level once more.
Why is my PetSafe bark collar not working?
Ensure that
the battery is properly installed. Replace the battery. If the Bark Control Collar still does not beep, contact the Customer Care Center at 1-800-732-2677.
How do I reset my PetSafe collar after replacing the battery?
Make sure the collar is powered on. Press and hold the button on the collar until a beep is heard and the light flashes green to turn the collar on.
Press and hold the power button for 10 seconds to reset the collar. The light turns red and the collar turns off.
How do I test my PetSafe wireless transmitter?
How do I test my PetSafe collar?
All you have to do is
hold the tool against the contact points on your dog or cat’s receiver collar to check if the collar is working properly. The test light tool will light up if static correction is being activated.
What is the button on the petsafe collar?
The slide buckle prevents the collar from becoming loose around your pet’s neck and the ridges must be facing up (3C). 6. While the receiver collar is still off your pet, turn it on by holding the
mode button until a green light comes on.
How do you reset a dog shock collar?
Press and hold the Upper Button on the Remote Transmitter until the Receiver Indicator Light flashes 5 times. You may need to hold both units 2-3 feet from each other before this occurs. Once the Receiver Indicator Light has flashed 5 times, the Collar Receiver has been reset and will begin flashing as normal.
How long do petsafe wireless collars last?
The Wireless Containment System unit can last up to
approximately 10 years or more if used properly. Batteries on the collar can last and be replaced up to 1 to 2 months.
Why is my dog’s shock collar blinking red?
If you have started to see a red flashing light on your pet’s Computer Collar unit,
your Power Cap battery may need to be replaced. You can order replacement batteries online, from your local dealer, or by calling 1-800-824-3647.
How do I sync my PetSafe wireless collar?
How do I change the settings on my PetSafe collar?
Why is my invisible fence collar blinking green?
The status light will double flash green every 30 seconds during the 24-hour period after the dog has entered the boundary area. This feature
monitors the voltage level of the battery. … If your light flashes double red, this indicates that your battery is low and your pet has challenged the dog containment system.
